He-Ne Lab Laser 0.8 mW / Class II Standard power He-Ne lab laser with modulation capability Industrial Fiber Optics' CT Series of lasers are the most popular line of lasers used in middle and high schools in the United States. Designed for education, and featuring a bright blue transparent enclosure, their attractive looks invite students to participate and explore in optical and laser technology while seeing the laser's internal "working" components. With a complete set of features and long warranty, it is a product that is hard to surpass. The IF HN08M is a unique laser created for the educational market. It has all the standard features and capabilities of a typical Class II helium-neon laser, but it also includes additional electronic circuits for demonstrating voice/audio (data) transmission over the laser beam. (When used a suitable receiver to "decode" the light beam into an audio signal.) Audio signal can be either from any dynamic microphone or any audio device. See operators manual for information on microphone, electrical connections and set-up instructions. A great multi-function laser for doing basic laser, optical and data transmission demonstrations. The CT Series lasers were designed for use in education. They are not an engineering product or design being sold for educational purposes. From the initial concept everything about the attractive, safe design was to interest students in technology. It includes safety features such as 110 VAC to low voltage power adapters, tamper-resistant screws, impact resistant acrylic enclosure, easily locatable bright red laser shutter, bright and very durable nickel-plated laser aperture, industry standard electrical connections and tripod mount. |
Other products for use this with laser:
|
- Hard-seal laser tube for long dependable life
- All solid-state electronic design
- Fool-proof mechanical beam stop
- Bright laser pilot light
- Impact-resistant, see-through, two-tone blue acrylic case
- Tamper-resistant screws for safety
- Threaded mounts for holding lenses, filters, and diffraction gratings
- Tripod mount - 1/4-20 thread
- Rubber feet on chassis bottom for adhesion on slick lab surfaces
- Full-color operator's manual with safety information and common experiments
- Labeling and safety requirements compliant with U.S. CDHR regulations
- 110 VAC operation; 220 VAC upon request. Please read the Step-Down-Transformer-101.pdf to see what is available. Then select the part number required.
- Refraction
- Reflection
- Tyndall's light-guiding-in-water experiments
- Scattering of Light li>Critical angle determination in materials
- Convergence and divergence of lenses
LASER CLASSIFICATIONS
All manufacturers of lasers used in the United States, must conform to regulations administered by the Center for Devices and Radiological Health (CDRH), a branch of the U.S. Department of Health and Human Services. CDRH categorizes lasers as follows:
A laser or laser system which does not present a hazard to skin or eyes for any wavelength or exposure time. Exposure varies with wavelength. For ultraviolet, .2 to .4µm exposure is less than from .8 or near IR, the exposure is < 200µw. Consult CDRH regulations for specific information.
Any visible laser with an output less than 1 mW of power. Warning label requirements - yellow caution label stating maximum output of 1 mW. Generally used as classroom lab lasers, supermarket scanners and laser pointers.
Any visible laser with an output over 1 mW of power with a maximum output of 5 mW of power. Warning label requirements - red danger label stating maximum output of 5 mW. Also used as classroom lab lasers, in holography, laser pointers, leveling instruments, measuring devices and alignment equipment.
Any laser with an output over 5 mW of power with a maximum output of 500 mW of power and all invisible lasers with an output up to 400 mW. Warning label requirements - red danger label stating maximum output. These lasers also require a key switch for operation and a 3.5-second delay when the laser is turned on. Used in many of the same applications as the Class IIIa when more power is required.
Any laser with an output over 500 mW of power. Warning label requirements - red danger label stating maximum output. These lasers are primarily used in industrial applications such as tooling, machining, cutting and welding. Most medical laser applications also require these high-powered lasers.
Specifications | ||
CDRH Classification | Class II | |
Polarization | Random | |
Laser Emission Color | Red | |
Laser Mode | TEM00 | |
Operating | Unit | Value |
Input Voltage | V | 12 to 18 |
Input Current | mA | 650 |
Wavelength | nm | 632.8 |
Optical Output Power, Nominal | mW | 0.8 mW / |
Power, (min/max) | mW | .6 / 1.0 |
Beam Diameter | mm | 0.47 |
Beam Divergence | mRad | 1.00 |
Digital Modulation | MHz | n/a |
Analog Modulation | Hz to MHz | 600 - 20K |
Mechanical | Unit | Value |
Operating Temperature | ° C | 0 - 40 |
Housing | cm | 5.8 x 8.7 x 36.2 |